ADVANTAGES
特点
●可容许较少肉厚的设计.
●可使用热溶或超音波的方式快速装置.
●阶段性之外径设计，渐进式嵌入塑胶，母材料塑胶不易龟列
● Permits thin boss walls allowing compact boss design ● Provides high torque and pull out performance ● Rapid installation using heat or ultrasonic
● Self-aligning Assists Installation ●相反方向之双斜花纹设计，与塑胶紧密结合，扭拉力极强. SELECTION OF INSERT OR STUD
INSERTS
HEADED INSERTS
STUDS
HEADED STUDS
PRODUCT CODE(SL) ISO METRIC(公制)
Product Code 型
Thread Size 螺牙
Insent Length A 标准长度
PORDUCT CODE(SHK) PRODUCT CODE(SLTS) PRODUCT CODE(SLHS)
Preferred Other
Length A* 特殊长度
Stud Lengths (For SLTS & SLHS only)
S 公件长度
Head Height B 头厚
Head ФC 头外径
Insert ФD 外径
PilotEnd ФP 圆头
Rec.Hole Size -0.00 +0.10 孔直径
Min.Wall Thickness 最少 肉厚
M1 M1.2 M1.4 M1.6 M1.7 M2
SL-B SHK-B SLTS-B SLHS-B
M3 M3.5 M4 M5 M6 M8 M10 M12 M2.5
1.5 2.0 2.5 3.0 3.0 4.0 5.7 5.7 7.1 8.1 9.5 12.7 12.7 12.7 15.9
- -
- - 1.70 1.70 2.10 2.10 2.10 3.1 3.9 3.9 4.7 5.5 6.3 7.9 9.5 11.8 15.8
1.55 1.75 2.15 2.15 2.15 3.2 4.0 4.0 4.8 5.6 6.4 8.0 9.6 11.9 16.0
0.70 0.70 0.80 0.80 0.80 1.3 1.6 1.6 1.8 2.1 2.6 3.3 4.5 6.0 8.0
Other lengths possible on quotation 其它长度也可估价 UNIFLED(英制)
Product
Code
型
Thread Size 螺牙
Insent Length A 标准 长度
Preferred Other Length
A* 特殊长度
Stud Lengths (For SLTS & SLHS only)
S 公件长度
Head
Height
Head Ф C 头外径
Insert Ф D 外径
PilotEnd Ф P 圆头
Rec.Hole Size -0.00 +0.04 孔直径
Min.Wall Thickness 最少 肉厚
B 头厚
5/165/165/165/165/165/16
3/83/83/83/83/83/83/83/83/83/83/83/83/83/83/8
7/167/167/167/167/167/167/167/167/167/167/167/167/167/167/16
1/21/21/21/21/21/21/21/21/21/21/21/21/21/21/2
5/85/85/85/85/85/85/85/85/85/85/85/85/85/85/8
3/43/43/43/43/43/43/43/43/43/43/43/43/43/43/4
7/87/87/87/87/87/87/87/87/87/87/87/87/87/87/8
.236 -
-
.469
SL-B SHK-B
SLTS-B
SLHS-B
5/165/165/165/165/165/165/16- 1/2
-
- - 5/16
5/16
Other lengths possible on quotation 其它长度也可估价 SPECIFYING AN INSERT & STUD
INSERTS(METRIC)
B X
.157
X INSERTS(METRIC)
4.0
PRODUCT CODE
-MATERIAL
X STUD LENGTH
PREFERREO CODE
SIZE
OTHER LENGTH
THREAD SIZE
OTHER LENGTH
B
X
INSERTS(IMPERIAL)
BOSS DESIGN SPECIFICATION HOLE PREPARATION
Moulded Holes are recommended wherever possible. The taper on a moulded hole should bi I。
Inclusive and the hole diameter
recommended should apple at the point reached by the bottom of the insert. Drilled holes may be used but performance may be reduced when compared with a moulded hole. The top of the hole should not be chamfered or counterbored and care must be taken to avoid bell mouthing. Hole diameter tolerance:-0.00+0.10mm
WALL THICKNESS
A general guide to minimum wall thickness is given in the data table but this will vary depending upon the nature of the plastic. Where thinner wall are required these can often be accommodated, but consultation with the Technology Centre of Local Sales Office and pre-production testing is strongly advised.
INSTALLATION
The fastener may be installed using either a pre-heating process of
Using heat generated by ultrasonic vibrations. Where preheating is used, care must be exercised to ensure that the fastener softens but does not melt the plastic. This will avoid any tendency to generate unsightly flash around the top of the insert. Ultrasonic installation is best carried out using low amplitude vibration and the minimum power consistent with satisfactory softening of the plastic material.
In either case excessive pressure should be avoided, since this may result in the insert being forced into the hole without allowing the plastic to soften and flow around the surface profile.
PERFORMANCE DATA
The complexity of materials and variations in service conditions make It impossible to detail fastener performance for specific applications. The chart below gives a general guide and show the relative performance of the inserts in the range.
STUDS(IMPERIAL)
塑胶孔径之设计 1. 各规格螺母之塑胶建议孔径，请参考规格表。 2. 塑胶孔径内之脱模斜度应于1度以内。
3. 塑胶内孔径之公差应设计在-0.00+0.10mm的范围。 4. 塑胶孔上方可以不设计导角。
塑胶孔肉厚 1. 建议肉厚，请参考规格表。
2.
肉厚可视不同塑胶材质，而略作调整，但请先与相关技术人员联系，必要时我们将协助测试及作最适当之建议。 装置 1. 可使用热熔; 超音波或射出成型中埋入。
2. 热熔温度不可超过塑胶材质之熔点，应低于熔点10-20度。3.
使用热熔及超音波埋入螺母时，所设定之压力、时间、速度，需视所使用之螺母规格及塑胶材料种类来调理想值。 4.
射出成型中埋入时，请特别注意模具上所使用套筒尺寸，须配合螺母之内孔径公差范围，切勿大于公差之下限值，请于开模前咨询相关技术人员，以取得建议值。
测试数据 1.
为服务客户，非常欢迎客户委托代作测试，我们将提供完整及详细之测试报告及必要之建议。 2.
使用各种精密测试仪器，针对常用之塑胶材料作出各类型螺母可承爱拉力的测试数据请参考。
ADVANTAGES
特点
● Re-usable threads for miniature applications ●针对迷你型产品设计. ● Eliminates thread striping problems ●可防止螺牙滑牙.
● Double ended-assists automatic feeding ●外形无方向型，方便自动养料加工. ● Permits space-saving boss desing ●可节省塑胶肉厚空间的设计.
HEADED
PRODUCT CODE(MTEC)
ISO METRIC(公制)
Product Code 型
Thread Size 螺牙
Insent Length A 标准长度
PORDUCT CODE(HMTEC)
Preferred Other
Length A* 特殊长度
Head Height B 头厚
Head Ф C
头外径
Insert ФD 外径
PilotEnd ФP 圆头
Rec.Hole Size -0.00 +0.10 孔直径
Min.Wall Thickness
最少肉厚
3.0SL-B SHK-B SLTS-B SLHS-B
3.03.02.03.05.0Other lengths possible on quotation 其它长度也可估价.
SPECIFYING AN INSERT & STUD
INSERTS(METRIC)
B
X
2.0
CODE SIZE OTHER LENGTH
型号
材质
螺牙
特殊长度
B 2.5
BOSS DESIGN SPECIFICATION HOLE PREPARATION
Moulded holes are recommended wherever possible. The taper on a moulded hole should be 0.5。
inclusive and the hole diameter recommended should apply at the point reached by hole bottom of the insert. The of the hole should not be chamfered or counterbored and care must be taken to avoid bell mouthing. Hole diameter tolerance: -0.00 +0.05mm.
INSTALLATION
The fastener has been designed for installation using a pre-heating process. Care must be exercised to ensure that the fastener softens but does not melt the plastic. This will avoid any tendency to generate be avoided, since this may result in the insert being forced onto the hole without allowing the plastic to soften and flow around the surface profile.
WALL THICKNESS
A general guide to minimum wall thickness is given in the data table but this vary depending upon the nature of the plastic. Where thinner wall are required these can often be accommodated, but consultation with the Technology Center or Local Sales Office and pre-production testing is strongly advised.
PERFORMANCE DATA
The complexity of materials and variations in service conditions make it impossible to detail fastener performance for specific applications. please consults Technology Centre or local sales offices for specific application advice.
塑胶孔径之设计 1. 螺母规格之塑胶孔建议值，请参考规格表。 2. 塑胶成型后，内孔径之脱模斜度应于0.5度以内。 3. 塑胶内孔径公差值请设于0.00+0.05mm的范围。 4. 塑胶内孔上方，可不必设计导角。
装置 1. 适用于射出成型或热熔加工。
2. 射出成型埋入时，请特别注意模具中套筒尺寸，以方便螺母置入模具中。3. 套筒尺寸公差请参阅建议值或洽技术人员。 4. 热熔加工时，温度抵母材熔点10-20度。
5. 热熔加工所须之压力、时间及速度，须视塑胶材质及螺母大小而调整。
塑胶孔内厚 1. 建议肉厚，请参考规格表。
2.
肉厚可视不同塑胶材质，而略作调整，但请先与相关技术人员联系。必要时我们将协助测试及作最适当之建议。
测试数据 1.
为服务客户，非常欢迎客户委托代作测试，我们将提供完整及详细之测试报告及必要之建议。
ADVANTAGES
特点
●可容许较少肉厚的设计.
●可使用热溶或超音波的方式快速装置.
●阶段性之外径设计，渐进式嵌入塑胶，母材料塑胶不易龟列
● Permits thin boss walls allowing compact boss design ● Provides high torque and pull out performance ● Rapid installation using heat or ultrasonic
● Self-aligning Assists Installation ●相反方向之双斜花纹设计，与塑胶紧密结合，扭拉力极强. SELECTION OF INSERT OR STUD
INSERTS
HEADED INSERTS
STUDS
HEADED STUDS
PRODUCT CODE(SL) ISO METRIC(公制)
Product Code 型
Thread Size 螺牙
Insent Length A 标准长度
PORDUCT CODE(SHK) PRODUCT CODE(SLTS) PRODUCT CODE(SLHS)
Preferred Other
Length A* 特殊长度
Stud Lengths (For SLTS & SLHS only)
S 公件长度
Head Height B 头厚
Head ФC 头外径
Insert ФD 外径
PilotEnd ФP 圆头
Rec.Hole Size -0.00 +0.10 孔直径
Min.Wall Thickness 最少 肉厚
M1 M1.2 M1.4 M1.6 M1.7 M2
SL-B SHK-B SLTS-B SLHS-B
M3 M3.5 M4 M5 M6 M8 M10 M12 M2.5
1.5 2.0 2.5 3.0 3.0 4.0 5.7 5.7 7.1 8.1 9.5 12.7 12.7 12.7 15.9
- -
- - 1.70 1.70 2.10 2.10 2.10 3.1 3.9 3.9 4.7 5.5 6.3 7.9 9.5 11.8 15.8
1.55 1.75 2.15 2.15 2.15 3.2 4.0 4.0 4.8 5.6 6.4 8.0 9.6 11.9 16.0
0.70 0.70 0.80 0.80 0.80 1.3 1.6 1.6 1.8 2.1 2.6 3.3 4.5 6.0 8.0
Other lengths possible on quotation 其它长度也可估价 UNIFLED(英制)
Product
Code
型
Thread Size 螺牙
Insent Length A 标准 长度
Preferred Other Length
A* 特殊长度
Stud Lengths (For SLTS & SLHS only)
S 公件长度
Head
Height
Head Ф C 头外径
Insert Ф D 外径
PilotEnd Ф P 圆头
Rec.Hole Size -0.00 +0.04 孔直径
Min.Wall Thickness 最少 肉厚
B 头厚
5/165/165/165/165/165/16
3/83/83/83/83/83/83/83/83/83/83/83/83/83/83/8
7/167/167/167/167/167/167/167/167/167/167/167/167/167/167/16
1/21/21/21/21/21/21/21/21/21/21/21/21/21/21/2
5/85/85/85/85/85/85/85/85/85/85/85/85/85/85/8
3/43/43/43/43/43/43/43/43/43/43/43/43/43/43/4
7/87/87/87/87/87/87/87/87/87/87/87/87/87/87/8
.236 -
-
.469
SL-B SHK-B
SLTS-B
SLHS-B
5/165/165/165/165/165/165/16- 1/2
-
- - 5/16
5/16
Other lengths possible on quotation 其它长度也可估价 SPECIFYING AN INSERT & STUD
INSERTS(METRIC)
B X
.157
X INSERTS(METRIC)
4.0
PRODUCT CODE
-MATERIAL
X STUD LENGTH
PREFERREO CODE
SIZE
OTHER LENGTH
THREAD SIZE
OTHER LENGTH
B
X
INSERTS(IMPERIAL)
BOSS DESIGN SPECIFICATION HOLE PREPARATION
Moulded Holes are recommended wherever possible. The taper on a moulded hole should bi I。
Inclusive and the hole diameter
recommended should apple at the point reached by the bottom of the insert. Drilled holes may be used but performance may be reduced when compared with a moulded hole. The top of the hole should not be chamfered or counterbored and care must be taken to avoid bell mouthing. Hole diameter tolerance:-0.00+0.10mm
WALL THICKNESS
A general guide to minimum wall thickness is given in the data table but this will vary depending upon the nature of the plastic. Where thinner wall are required these can often be accommodated, but consultation with the Technology Centre of Local Sales Office and pre-production testing is strongly advised.
INSTALLATION
The fastener may be installed using either a pre-heating process of
Using heat generated by ultrasonic vibrations. Where preheating is used, care must be exercised to ensure that the fastener softens but does not melt the plastic. This will avoid any tendency to generate unsightly flash around the top of the insert. Ultrasonic installation is best carried out using low amplitude vibration and the minimum power consistent with satisfactory softening of the plastic material.
In either case excessive pressure should be avoided, since this may result in the insert being forced into the hole without allowing the plastic to soften and flow around the surface profile.
PERFORMANCE DATA
The complexity of materials and variations in service conditions make It impossible to detail fastener performance for specific applications. The chart below gives a general guide and show the relative performance of the inserts in the range.
STUDS(IMPERIAL)
塑胶孔径之设计 1. 各规格螺母之塑胶建议孔径，请参考规格表。 2. 塑胶孔径内之脱模斜度应于1度以内。
3. 塑胶内孔径之公差应设计在-0.00+0.10mm的范围。 4. 塑胶孔上方可以不设计导角。
塑胶孔肉厚 1. 建议肉厚，请参考规格表。
2.
肉厚可视不同塑胶材质，而略作调整，但请先与相关技术人员联系，必要时我们将协助测试及作最适当之建议。 装置 1. 可使用热熔; 超音波或射出成型中埋入。
2. 热熔温度不可超过塑胶材质之熔点，应低于熔点10-20度。3.
使用热熔及超音波埋入螺母时，所设定之压力、时间、速度，需视所使用之螺母规格及塑胶材料种类来调理想值。 4.
射出成型中埋入时，请特别注意模具上所使用套筒尺寸，须配合螺母之内孔径公差范围，切勿大于公差之下限值，请于开模前咨询相关技术人员，以取得建议值。
测试数据 1.
为服务客户，非常欢迎客户委托代作测试，我们将提供完整及详细之测试报告及必要之建议。 2.
使用各种精密测试仪器，针对常用之塑胶材料作出各类型螺母可承爱拉力的测试数据请参考。
ADVANTAGES
特点
● Re-usable threads for miniature applications ●针对迷你型产品设计. ● Eliminates thread striping problems ●可防止螺牙滑牙.
● Double ended-assists automatic feeding ●外形无方向型，方便自动养料加工. ● Permits space-saving boss desing ●可节省塑胶肉厚空间的设计.
HEADED
PRODUCT CODE(MTEC)
ISO METRIC(公制)
Product Code 型
Thread Size 螺牙
Insent Length A 标准长度
PORDUCT CODE(HMTEC)
Preferred Other
Length A* 特殊长度
Head Height B 头厚
Head Ф C
头外径
Insert ФD 外径
PilotEnd ФP 圆头
Rec.Hole Size -0.00 +0.10 孔直径
Min.Wall Thickness
最少肉厚
3.0SL-B SHK-B SLTS-B SLHS-B
3.03.02.03.05.0Other lengths possible on quotation 其它长度也可估价.
SPECIFYING AN INSERT & STUD
INSERTS(METRIC)
B
X
2.0
CODE SIZE OTHER LENGTH
型号
材质
螺牙
特殊长度
B 2.5
BOSS DESIGN SPECIFICATION HOLE PREPARATION
Moulded holes are recommended wherever possible. The taper on a moulded hole should be 0.5。
inclusive and the hole diameter recommended should apply at the point reached by hole bottom of the insert. The of the hole should not be chamfered or counterbored and care must be taken to avoid bell mouthing. Hole diameter tolerance: -0.00 +0.05mm.
INSTALLATION
The fastener has been designed for installation using a pre-heating process. Care must be exercised to ensure that the fastener softens but does not melt the plastic. This will avoid any tendency to generate be avoided, since this may result in the insert being forced onto the hole without allowing the plastic to soften and flow around the surface profile.
WALL THICKNESS
A general guide to minimum wall thickness is given in the data table but this vary depending upon the nature of the plastic. Where thinner wall are required these can often be accommodated, but consultation with the Technology Center or Local Sales Office and pre-production testing is strongly advised.
PERFORMANCE DATA
The complexity of materials and variations in service conditions make it impossible to detail fastener performance for specific applications. please consults Technology Centre or local sales offices for specific application advice.
塑胶孔径之设计 1. 螺母规格之塑胶孔建议值，请参考规格表。 2. 塑胶成型后，内孔径之脱模斜度应于0.5度以内。 3. 塑胶内孔径公差值请设于0.00+0.05mm的范围。 4. 塑胶内孔上方，可不必设计导角。
装置 1. 适用于射出成型或热熔加工。
2. 射出成型埋入时，请特别注意模具中套筒尺寸，以方便螺母置入模具中。3. 套筒尺寸公差请参阅建议值或洽技术人员。 4. 热熔加工时，温度抵母材熔点10-20度。
5. 热熔加工所须之压力、时间及速度，须视塑胶材质及螺母大小而调整。
塑胶孔内厚 1. 建议肉厚，请参考规格表。
2.
肉厚可视不同塑胶材质，而略作调整，但请先与相关技术人员联系。必要时我们将协助测试及作最适当之建议。
测试数据 1.
为服务客户，非常欢迎客户委托代作测试，我们将提供完整及详细之测试报告及必要之建议。